RIM CENTER DESIGN'S

WE HAVE TON'S OF DESIGN'S IN HOUSE (MOST ARE NOT SHOWN-TOO MANY TO POST UP HERE). WE ALSO CAN CUT A CUSTOM DESIGN FOR YOU THAT'S YOUR DESIGN A ONE OFF ONLY THAT NO ONE ELSE CAN HAVE. PLEASE CALL FOR DETAILS. 

WE SELL RIM CENTERS FOR ALL STEEL RIMS (ONLY), RIM CENTERS RANGE IN DIAMETER/THICKNESS/DESIGN/LUG PATTERN

(CENTER PLATE DIAMETER NOT THE SAME AS RIM DIAMETER)

 3/8" PLATE CENTERS RANGE FROM $75.00 EACH FOR 13" DIAMETER UP TO $250.00 EACH FOR 34" DIAMETER

1/2" PLATE CENTERS RANGE FROM $85.00 EACH FOR 13" DIAMETER UP TO $300.00 EACH FOR 34" DIAMETER 

5/8" PLATE CENTERS RANGE FROM $95.00 EACH FOR 13" DIAMETER UP TO $350.00 EACH FOR 34" DIAMETER

NOTE: NOT ALL RIM'S THAT SHARE THE SAME SIZE DIAMETER AND WIDTH SHARE THE SAME SIZE CENTER, THEY VARY BY MANUFACTURE AND MODEL. EXAMPLE A 26" DIAMETER RIM MAY HAVE A CENTER THAT IS 22 1/8" OR 23 7/8" DIAMETER CENTER PLATE

***THE AVERAGE 24" TO 26" DIAMETER WHEEL

USE'S A RIM CENTER PLATE THAT IS SMALLER THAN 24" DIAMETER WILL COST YOU***

$125.00 FOR 3/8" DIAMETER

$150.00 FOR 1/2" DIAMETER

$175.00 FOR 5/8" DIAMETER

ALL COMPLETE RIMS OR RIM CENTER PLATES COME WITH YOUR CHOICE OF LUG PATTERN AND DESIGN, & ALL THE LUG HOLES ARE CHAMFERED ON BOTH SIDES

WE BUILD UP TO 46" DIAMETER WHEELS

***WE SELL ALL KINDS OF RIM SHELLS, RIM BLANKS, RIM HOOPS, RIM BARRELS

CALL FOR PRICING ASK FOR PARTS OR SERVICE***

HERE @ RBC WE USE THE FOLLOWING STEEL PLATE THICKNESS 3/8" OR 1/2" OR 5/8" DEPENDING ON DIAMETER AND DESGN

***WE USE A SNAP-ON 350 AMP INDUSTRIAL MIG WELDER THAT WE CUSTOM STITCH WELD YOUR CENTERS FOR THAT CLEAN STACK OF OVER-LAPPING DIMES LOOK***

WHEN YOU ARE PLACING YOUR WHEEL ORDERS

PLEASE GIVE US THE FOLOWING INFO: WE NEED YOUR TIRE SIZE/MAKE/MODEL

FOR THE CORRECT RIM-TIRE PROFILE

WHEEL DIAMETER  X  WIDTH  X PLATE THICKNESS  X LUG PATTERN  X BACK SPACE  X DESIGN  X COLOR & VALVE HOLE DIAMETER AND LOCATION

(ON LARGE TRACTOR TIRE TRUCKS WE RECOMMEND THE VALVE STEM BE ON THE INSIDE OF THE RIM SO YOU DONT STEP ON IT EVERY TIME YOU CLIMB IN YOUR TRUCK)

BACK SPACING IS MEASURED FROM THE OUTSIDE EDGE OF THE RIM AS ITS LAYING FLAT ON A STEEL WELDING TABLE TO THE BOTTOM OF THE STEEL PLATE CENTER.

PLEASE SPECIFY IF YOU WANT THE VALVE STEM HOLE FACING OUT OR ON THE INSIDE

ADD SOLID PAINT: INCLUDES SAND BLAST, EXPOXY PRIMER, AND YOUR SOLID COLOR OF CHOICE $50.00 EACH WHEEL

ADD METALIC PAINT: INCLUDES SAND BLAST, EXPOXY PRIMER, AND YOUR SOLID COLOR OF CHOICE $75.00 EACH WHEEL

NOTE: WE DO NOT USE A RATTLE CAN FOR PAINT, THESE ARE SENT OUT TO A BODY SHOP

ADD POWDER COAT: (800 COLORS TO CHOOSE FROM) INCLUDES SAND BLAST, 2 COATS OF COLOR, 1 COAT OF CLEAR $150.00 EACH WHEEL

NO CHROME AVAILIBLE AT THIS TIME

(IF YOU HAVE A CUSTOM CROME SHOP FOR ALL PARTS PLEASE LET RBC KNOW)

ARE YOU LOOKING FOR A CUSTOM WIDTH RIM THAT IS NOT SHOWN IN SIZE?.......WE CAN DO THAT BY DOING THE FOLLOWING, WE HAVE TO CUT DOWN A KNOWN SIZE RIM, ROLL A HOOP AND WELD THE SEAM TO FORM A BARREL ROLL, AND THEN WELD THE BARREL ROLL INTO THE 2 PARTS OF THE CUT IN HALF RIM SHELL. THERE WILL BE AN EXTRA CHARGE FOR PARTS AND LABOR. ALSO AN EXTRA CHARGE IF YOU WOULD LIKE ALL THE WELDS GROUND DOWN TO LOOK LIKE THE WHEEL IS ALL ONE PIECE....CALL PARTS/SERVICE FOR INFO & 810-650-8641 PARTS/SERVICE

15" RIMS

ALL RIMS BUILT WITH 3/8" SOLID PLATE

UNLESS UP GRADED TO 1/2" SOLID PLATE (ADD $25.00 PER RIM)

TRUCK MOCK UP SPECIALS WHEELS 15" X 7" OR 15" X 8" X .250" PLATE STEEL X 6 LUG (ONLY) ROCKWELL $125.00 EACH (THESE ARE FOR MOVING THE TRUCK AROUND THE SHOP OR TO PUT TRUCK INSIDE OF A TRAILER. NOT FOR ANY TYPE OF ABUSE)

15" X 10" $200.00 EACH    15" X 12" $215.00 EACH   15" X 14" $225.00 EACH

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $75.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS NOT A LOT OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

16" RIMS

ALL RIMS BUILT WITH 3/8" PLATE

UNLESS UP GRADED TO 1/2" PLATE (ADD $25.00 PER RIM)

TRUCK MOCK UP SPECIALS WHEELS 16" X 7" OR 16" X 8" X .250" PLATE STEEL X 6 LUG ROCKWELL $125.00 EACH (THESE ARE FOR MOVING THE TRUCK AROUND THE SHOP OR TO PUT TRUCK INSIDE OF A TRAILER. NOT FOR ANY TYPE OF ABUSE)

16" X 10" $200.00 EACH    16" X 12" $215.00 EACH   16" X 14" $225.00 EACH

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $75.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS NOT A LOT OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

16.1" RIMS

ALL RIMS BUILT WITH 3/8" SOLID PLATE

UNLESS UP GRADED TO 1/2" SOLID PLATE (ADD $25.00 PER RIM)

16.1" DIAMETER X 16" WIDE (ONLY)

$250.00 EACH

SPECIFY 6 LUG ROCKWELL OR 10 LUG ROCKWELL

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $75.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS NOT A LOT OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

16.5" RIMS

ALL RIMS BUILT WITH 3/8" SOLID PLATE

UNLESS UP GRADED TO 1/2" SOID PLATE (ADD $25.00 PER RIM)

TRUCK MOCK UP SPECIALS WHEELS 16.5" X 7" OR 16.5" X 8" X .250" PLATE STEEL X 6 OR 10 LUG ROCKWELL $125.00 EACH (THESE ARE FOR MOVING THE TRUCK AROUND THE SHOP OR TO PUT TRUCK INSIDE OF A TRAILER. NOT FOR ANY TYPE OF ABUSE)

16.5" X 10" $200.00 EACH    16.5" X 12" $215.00 EACH   16.5" X 14" $225.00 EACH

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $75.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS NOT A LOT OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

17" DIAMETER RIMS ARE NOT AVAILIBLE AT THIS TIME. OUR RIM SUPPLIER

IS NO LONGER MAKENG THEM AT THIS TIME

20" RIMS FOR MILITARY MICHELIN OR GOOD YEAR TIRES

THIS COVERS ALL THE 46" UP TO 53" TIRES

(12.00 TO 16.00 X 20)

ALL THE MILITARY RIMS ARE BUILT WITH 1/2" SOLID PLATE STANDARD OR 5/8" UPGRADE

ADD AN UP GRADED DESIGN FOR FREE

5/8"  PLATE (ADD $25.00 PER RIM)

   STANDARD 20" X 11" WITH 1/2" PLATE CENTER  $275.00 EACH   

(CAN NOT USE ANY WIDER OF A RIM DUE TO HOW THICK THE SIDE WALL OF THE TIRE IS. IT WILL NOT SPREAD OUT TO A 14" WIDE RIM. THE TIRES AVERAGE 22 OT 24 PLY PAY LOADER STYLE BEADS. THIS IS WHY RECOMMEND THE "ROCK GUARDS" AT LEAST ON THE OUTSIDE OF THE RIM)

RBC HIGHLY RECOMMENDS THESE "ROCK GUARDS" FOR 2 REASONS, THE SIDE WALLS OF THESE TIRES ARE PAY LOADER BEADS WHCH ARE OVER 1" THICK AND REQUIRE "SOME MANUAL LABOR" TO INSTALL THESE ONTO A 1 PIECE RIM. WE HAVE INSTALLED 400-500 OF THESE AND THEY DO GO ON. SOME TIMES THE RIM BENDS BEFORE THE TIRE GIVES AND WITH THE "ROCK GUARDS" WELDED IN THIS WILL NOT HAPPEN. THE SECOND REASON IS THE COOL FACTOR...THEY LOOK SWEET WITH THIS OPTION.

ROCK GUARDS 1/4" PLATE ADD $125.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

***MILITARY MICHELIN'S/GOOD YEAR'S  12.00 THRU 16.00 X 20" DIA USE 11" WIDE

WITH 1/2" OR UPGRADED 5/8" STEEL PLATE ONLY***

20" RIMS (FOR NON MILITARY TIRES)

**ALL RIMS BUILT WITH 3/8" SOLID PLATE UNLESS UP GRADED**

UP GRADED TO 1/2" SOLID PLATE (ADD $25.00 PER RIM)

UP GRADED TO 5/8" SOLID PLATE (ADD $50.00 PER RIM)

ANY UP GRADE DESIGN-RBC ONLY CUTS A DESIGNER CENTER ON 1/2" PLATE (FREE PER RIM)

TRUCK MOCK UP SPECIALS WHEELS 20" X 9.25" X .250" PLATE STEEL X 6 OR 10 LUG ROCKWELL $175.00 EACH (THESE ARE FOR MOVING THE TRUCK AROUND THE SHOP OR TO PUT TRUCK INSIDE OF A TRAILER. NOT FOR ANY TYPE OF ABUSE)

20" X 9.25" $225.00 EACH    20" X 11" $250.00 EACH   20" X 14" $275.00 EACH

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $125.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS SEVERAL INCHES OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

24" RIMS

**ALL RIMS BUILT WITH 3/8" SOLID PLATE UNLESS UP GRADED**

UP GRADED TO 1/2" SOLID PLATE (ADD $25.00 PER RIM)

UP GRADED TO 5/8" SOLID PLATE (ADD $50.00 PER RIM)

ANY UP GRADE DESIGN-RBC ONLY CUTS A DESIGNER CENTER ON 1/2" PLATE (FREE PER RIM)

24" X 12" $275.00 EACH    24" X 15" $300.00 EACH   24" X 18" $325.00 EACH

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $125.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS SEVERAL INCHES OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

26" RIMS

**ALL RIMS BUILT WITH 3/8" SOLID PLATE UNLESS UP GRADED**

UP GRADED TO 1/2" SOLID PLATE (ADD $25.00 PER RIM)

UP GRADED TO 5/8" SOLID PLATE (ADD $50.00 PER RIM)

ANY UP GRADE DESIGN-RBC ONLY CUTS A DESIGNER CENTER ON 1/2" PLATE (FREE PER RIM)

26 X 16" $350.00 EACH    26" X 20" $400.00 EACH   

CALL FOR SPECIAL WIDTH'S

ROCK GUARDS 1/4" PLATE ADD $125.00 PER SIDE OF RIM (INCLUDES STEEL/LABOR)

NOTE: IF YOU WANT SOME KIND OF DESIGN CUT INTO THESE CENTERS THERE IS SEVERAL INCHES OF ROOM BETWEEN THE LUG PATTERN AND WHERE THE CENTER WELDS TO THE RIM

"RBC LARGE DIAMETER WHEELS" 

28" THRU 46" DIAMETER

CALL FOR SPECIAL PRICE'S

THESE LARGE RIMS USE ANY WHERE FROM

(4) CENTERS CUT OUT OF A 4' X 8' SHEET OF STEEL 

TO

(2) CENTERS CUT OUT OF A 4' X 8' SHEET OF STEEL

"MONSTER TRUCK RIMS"

25" DIAMETER X 32" OR 34" WIDE

***THIS IS THE REAL DEAL, RBC HAS TONS OF HOURS INTO EACH WHEEL THAT IS BUILT***

THIS RIM STARTS LIFE AS A BRAND NEW 25" X 13" WIDE WHEEL

WE CUT IT DOWN INTO 4 PEICES 

ROLL A PEICE OF SHEET METAL IN 10 OR 11 GAUGE INTO A TUBE

 HAVE IT LAZER WELDED FOR PRECISION

CHOICE OF 3/8" OR 1/2" CENTER PLATE

5 TON OR ANY PLANETARY LUG PATTERN

(40) BOLT BEAD LOCK (OUTER END OF RIM)

WITH 1/2" ROUND STOCK

ROLLED AND WELDED INTO INNER & OUTER LIPS OF RIM

$1650.00 EACH

IF YOU BUY OVER 40 AT ONCE WE WILL OFFER THEM AT $1550.00 EACH

OPTION: SAND BLAST, EPOXY PRIMER, & PAINT YOUR CHOICE OF COLOR $100.00 EACH

*ALL PRICE'S SUBJECT TO MARKET CHANGE*