2.5 TON ROCKWELL STUD GIRDLE'S

THESE HELP KEEP THE MAIN BEARING CAPS FROM PULLING DOWN AND SPREADING CAUSING MAJOR GEAR DAMAGE FROM HIGH HORSE POWER AND LARGE TIRES

GHE "ORIGINAL" STUD GIRDLE KIT

$195.00 EACH OR (2) FOR $390.00

GHE BILLET CAPS AND CARRIER ARE AN OPTIONAL UP-GRADE (AS SEEN ON LEFT) CALL FOR PRICE

OUVERSON STUD GIRDLE KIT

$195.00 EACH OR (2) FOR $390.00

2.5 TON ROCKWELL AXLE-TECH TIP

***STOCK CONFIGURATION AXLE DROP ON PASSENGER SIDE AND TIE BAR BEHIND AXLE***

***THE CHUNK ON A STEER AXLE CAN BE ROTATED 180* TO CENTER THE PINION OVER THE LONG SIDE AXLE SHAFT WITH SOME SMALL MODIFICATIONS (DRILLING & TAPPING) TO THE AXLE HOUSING***

***THE HUBS ON A STEER AXLE CAN BE FLIPPED INWARDS TO TRACK WITH A 2.5 TON ROCKWELL REAR STRAIGHT AXLE WITH SOME MODIFICATIONS (MACHINE WORK) TO THE HUBS AND CHANGING THE SPINDLE STUDS TO BOLTS. YOU HAVE TO RE TAP ALL THE HOLES DEEP WITH A 3/8" X TAP AND USE 3/8" X 16 X 1.50 LONG BOLTS***

2.5 TON ROCKWELL DRIVE FLANGE'S

USED STOCK 16 SPLINE $74.86 EACH

CLEAN & SAND BLASTED THESE USE PAPER GASKETS

OUVERSON 16 SPLINE

 PLEASE CALL FOR AVAILABILITY AND PRICING

THESE USE "O" RINGS

OUVERSON 47 SPLINE 2"

PLEASE CALL FOR AVAILABILITY AND PRICING

THESE USE "O" RINGS

2.5 TON ROCKWELL LOCK OUT HUBS

OUVERSON 16 SPLINE CAST 356 ALUMINUM

PLEASE CALL FOR AVAILABILITY AND PRICING

OUVERSON 47 SPLINE 2" BILLET ALUMINUM

PLEASE CALL FOR AVAILABILITY AND PRICING

2.5 TON ROCKWELL SPINDLE PARTS

3" OCTAGON NUT $7.50 EACH

SHOWN ON LEFT

LOCK TAB $6.85 EACH

SHOWN ON RIGHT

STOCK SPINDLE BUSHING $14.25 EACH

2" OUVERSON SPINDLE BUSHING $15.25 EACH

USED SPINDLE CLEANED & SAND BLASTED $130.00 EACH

FOR MACHINED STOCK SPINDLE  TO EXCEPT 2" OUVERSON AXLE SHAFTS ADD $75.00 EACH INCLUDES PRESSING IN 2" BUSHING

**COMING SOON** STEEL BILLET SPINDLE

SHOWN ON LEFT

3" OCTAGON SPINDLE SOCKET $40.00 EACH

SHOWN ON RIGHT 

2.5 TON ROCKWELL KING PIN PARTS

KING PIN UPPER BUSHING PLATES

(LEFT SIDE PICTURE) 

 $48.00 EACH

KING PIN LOWER BUSHING PLATES

(RIGHT SIDE PICTURE)

 $48.00 EACH

***NOTE WE CAN NO LONGER GET JUST THE BRASS BUSHING LOOSE ANY MORE FROM OUR WAREHOUSE***

***SOMETIMES DEPENDING ON MANUFACTURE & TIME PERIOD OF YOUR AXLE. YOU MAY HAVE TO GRIND DOWN THE OUTER DIAMETER OF THE BUSHING HOUSING TO MAKE IT FIT INTO THE KNUCKLE HOUSING***

KING PIN SHIMS (UPPER ONLY)

 $5.00 EACH

KING PIN FLAT PLATE $15.00 EACH

KING PIN FLAT PLATE BOLTS

NEW $3.00 EACH

 (REPLACE THAT STEER ARM WITH THIS CLEAN LOOK)

FACTORY STEER ARM KIT:

(4 STUDS, 4 CONES, 4 NUTS, 4 WASHERS)

$75.00 EACH

2.5 TON ROCKWELL STEERING KNUCKLES

ALL KNUCKLES COME CLEAN, SAND BLASTED, ALL 12 BOLT HOLES CHASED WITH A 3/8" X 16 TAP

STOCK RH KNUCKLE $175.00 EACH

SHOWN ON LEFT

STOCK LH KNUCKLE $175.00 EACH

SHOWN ON LEFT

WELDED & PLATED RH OR LH KNUCKLE WITH 3/4" OR 1" DIAMETER SLEEVE INSTALLED WITH GREASE FITTING FOR THE STRAIGHT BORE HOLE. WE COMPLETELY WRAP THE TOP/BOTTOM/SIDES/FRONT & BACK/ PLUS THE ENTIRE BODY OF THE KNUCKLE WITH 1/4" STEEL. THIS BLACK SMITHING PROCESS TAKES APROX 8 TO 10 HOURS FOR EACH KNUCKLE. WE EVEN CUT THE FACTORY STEERING STOPS OFF AND PLATE BEHIND THEM BEFORE WE INSTALL THEM IN THE CORRECT SPOT.THESE ARE BUILT ON A CUSTOM ORDER BASIS. THESE ARE BUILT FOR JUMPING...

WE NEED YOUR NON BROKEN KNUCKLE FOR A CORE PLUS  $375.00 EACH

WITH OUT CORE $475.00 EACH

SHOWN ON RIGHT AND BELOW FOR A BETTER VIEW

2.5 TON ROCKWELL TIE BARS

STOCK TIE BAR $175.00

            CUSTOM: WITH RH/LH 1" X 1/1/4" HEIMS WITH JAM NUTS, WELD IN BUNGS, & .250 WALL D.O.M. TUBE, (4) 3/4" MISALIGNMENT SPACERS, (2) 3/4" BOLTS WITH NUTS $375.00 COMPLETE

NOTE: IF YOU WANT TO STEP THIS UP TO A 1" BOLT YOU WILL HAVE TO USE WRAPPED KNUCKLES OTHER WISE THEY WILL FAIL

PLEASE SPECIFY STANDARD, SHORT OR LONG LENGTH

 2.5 TON ROCKWELL HUB

STOCK TAKE OFF HUB AS IS

$125.00 EACH

 DELUXE HUB:  CLEANED, SAND BLASTED, PRIMED AND PAINTED BLACK, 2 NEW WHEEL BEARINGS AND RACES, 6 NEW RH OR LH STUDS & LUG NUTS, 1  INNER AND OUTER WHEEL BEARING SEALS, 2 SPINDLE JAM NUTS, AND 1 SPINDLE LOCK TAB $375.00 COMPLETE

(AS SHOWN IN LEFT PICTURE)

OUVERSON WICKED 6 HUB  CNC BILLET MACHINED ALUMINUM

 PLEASE CALL FOR AVAILABILITY AND PRICING

 2.5 TON ROCKWELL 8 LUG ALUMINUM HUBS

 8 LUG CHEVY (8 ON 6 1/2")

OR

8 LUG FORD SUPER DUTY (8 ON 170 MM)

RED/BLUE/BLACK

OUVERSON SUPER 8 1.50" 16 SPLINE HUBS

PLEASE CALL FOR AVAILABILITY AND PRICING

OUVERSON SUPER 8 2" 47 SPLINE HUBS

PLEASE CALL FOR AVAILABILITY AND PRICING

2.5 TON ROCKWELL LUG'S & STUD'S

RH LUG NUT'S $3.00 EACH

LH LUG NUT'S $3.00 EACH

RH STUD'S $6.00 EACH

LH STUD'S $6.00 EACH

*NEW* LONGER STUDS RH & LH $7.50 EACH

*ALL PRICE'S SUBJECT TO MARKET CHANGE*